|
 |
|
|
|
|
|
|
Format |
ToolMod Module Size 2U |
|
|
Versions |
TM115h - horizontal Face Plate
TM115v - vertical Face Plate
|
|
|
Power Supply |
Tool-Series Standard |
|
|
Supply Voltages |
+/- 25 V and + 48 V Phantom |
|
|
Supply Current *) |
+/- 100 mA |
|
|
|
|
|
Input |
electronically balanced |
|
|
nominal Level |
+ 6 dBu - Gain |
|
|
maximum Level |
> + 30 dBu - Gain |
|
|
Input Impedance |
40 Hz - 15 kHz > 10 kOhms |
|
|
nominal Source Impedance |
50 Ohms |
|
|
CMRR |
15 kHz > 65 dB, typical 75 dB 1 kHz > 80 dB, 40 Hz > 90 dB |
|
|
|
|
|
Output |
electronically balanced |
|
|
nominal Level |
+ 6 dBu |
|
|
maximum Level |
> + 30 dBu |
|
|
Source Impedance |
50 Ohms, see Diagram
Output Source Resistance vs Frequency |
|
|
Load Resistor |
see Diagram
maximum Output Level vs Load Resistor
and
maximum Output Level vs capacitive Load |
|
|
CMRR according to IEC |
> 40 dB, siehe Diagram Output CMRR vs Frequency |
|
|
|
|
|
Gain |
0 dB +/- 0.2 dB no Regulation |
|
|
|
|
|
Frequency Response
|
20 Hz - 50 kHz +/- 0.2 dB no Regulation
- see Diagram Frequency Response
|
|
|
Bandwidth |
< 10 Hz to > 150 kHz |
|
|
|
|
|
Phase Response |
20 Hz-20 kHz < +6/-10°
- see Diagram Phase Response
|
|
|
|
|
|
THD |
< + 28 dBu, 40 Hz ... 20 kHz, < 0.1 %,
maximum THD at + 30 dBu <1 %
no Regulation
THD under regulation is determined by the frequency, attack and release settings, and the gain reduction |
|
|
|
|
|
Dynamic Range / Noise |
|
|
|
RMS 22Hz-22kHz |
<= -91 dBu no Regulation |
|
|
total Dynamic Range |
referring to the RMS Value 22Hz-22kHz
>= 121 dB no Regulation |
|
|
Control Voltage
Rejection |
> 70 dB |
|
|
|
|
|
Limiter |
very fast Peak Limiter |
|
|
Threshhold |
Control Range + 20 dB to - 10 dB, referring to + 6 dBu
0 dB Setting internally calibrated |
|
|
Attack |
Attack Time Adjustment for 10 dB Attenuation
Control Range 0.02 ms to 7 ms
(with short attack time, the period of the input signal determines the real attack time) |
|
|
Release |
Release Time Adjustment for 10 dB Gain Change
Control Range 50 ms to 3 s |
|
|
Display |
Gain reduction display with 5 LED's,
display range from 1 dB to 10 dB |
|
|
|
|
|
Bypass Circuitry |
Hardbypass by Relay |
|
|
|
|
|
*) The standard supply current is the supply current under realitic operation conditions. If the outputs are loaded with the minium load resistors and the level is at + 30 dBu, the supply current increases by 30 mA per output. The standard supply current shuold be used to calculate the necessary power supply capacity of a system. |
|
|
|
|
|
|
|
|