Technical Specifications
ToolMod TM130 & TM130m
M/S Direction Mixer with elliptical EQ
 OPEN IN NEW WINDOW/TAB | HOME | BACK  | TM130 HOME |CLOSE| INDEX 
Format ToolMod Module Size 2U
Versions TM130h - Recording Version - horizontal Face Plate
TM130v - Recording Version - vertical Face Plate
TM130m h - Mastering Version - horizontal Face Plate
TM130m v - Mastering Version - vertical Face Plate
Power Supply Tool-Series Standard
Supply Voltages +/- 25 V and + 48 V Phantom
Supply Current *) +/- 150 mA
Input electronically balanced
nominal Level + 6 dBu - Gain
maximum Level > + 30 dBu - Gain
Input Impedance 40 Hz - 15 kHz > 10 kOhms
nominal Source Impedance 50 Ohms
CMRR 15 kHz > 65 dB, typical 75 dB 1 kHz > 80 dB, 40 Hz > 90 dB
Output electronically balanced
nominal Level + 6 dBu
maximum Level > + 30 dBu
Source Impedance 50 Ohms, see Diagram
Output Source Resistance vs Frequency
Load Resistor see Diagram
maximum Output Level vs Load Resistor
and
maximum Output Level vs capacitive Load
CMRR according to IEC > 40 dB, see Diagram Output CMRR vs Frequency
Gain  0 dB +/- 0.3 dB - Input in LR-Modus, EEQ Off
Base Control and Direction Control at Center Position
Frequency Response
20 Hz - 50 kHz +/- 0.2 dB no Regulation
- see Diagram Frequency Response
Bandwidth < 10 Hz to > 150 kHz
Phase Response 20 Hz-20 kHz < +6/-10° linear setting
- see Diagram Phase Response
THD < + 28 dBu, 40 Hz ... 20 kHz, < 0.1 %,
maximum THD at + 30 dBu <1 %
Crosstalk Crosstalk is determined by the positions of the Base control and the Direction control, and the setting of the elliptical Equalizer.
With BASE = 100 %, DIR = C and EEQ Off
Crosstalk is > 45 dB in the range from 40 Hz to 15 kHz
Dynamic Range / Noise
RMS 22Hz-22kHz <= -90 dBu all operation modes at 0 dB Gain
total Dynamic Range referring to the RMS Value 22Hz-22kHz
>= 120 dB at 0 dB Gain
Function Stereo Direction Mixer with M/S Matrix and Controls for Base Width and Direction in the M/S chain; with input mode select XY / MS; includes an elliptical Equalizer
M/S Selection selects M/S mode for the input matrix instead of XY (Left - Right ) mode. (Left = M / Right = S).
Base Width (BASE) Recording Version:
Stereo Base Width Control by pot from
0 % = Mono, along
100 % = Stereo Original, calibrated, to
300 % = enhanced Base Width

Mastering Version:
Stereo Base Width Control by pot from
50 % = reduced Base Width
100 % = Stereo Original, calibrated, to
150 % = enhanced Base Width
Direction Control (DIR) Direction Control in the M/S path of the matrix
Recording Version, from
'Mono from Left' via 'Stereo normal' (calibrated) to
'Mono from Right'

Mastering Version
'+/- 6 dB Ranges with
'Stereo normal' (calibrated) at center
elliptical Equalizer
(EEQ)
Control of the Crosstalk level depending on the Frequency. Control Range from <40 Hz to 1 kHz with center detent
at 300 Hz.
The scaling refers to the frequency with 15 dB crosstalk
Steepness 6 dB/Okt.
separate Bypass Switch
Bypass Circuitry Hardbypass by Relay
*) The standard supply current is the supply current under realitic operation conditions. If the outputs are loaded with the minium load resistors and the level is at + 30 dBu, the supply current increases by 30 mA per output. The standard supply current shuold be used to calculate the necessary power supply capacity of a system.