| Technical Specifications |
STEREO COLORIZER U794 |
| Size |
Stereo in V700-Module 1N |
|
| Input |
|
| Type |
balanced, grounded |
| nominal Level |
+ 6 dBu |
| maximum Level1) |
ƒ ³ 40 Hz ³ + 30 dBu |
| Input Impedance |
ƒ 40 Hz - 15kHz ³ 5 kW |
| CMRR |
ƒ 40 Hz - 15 kHz ³ 60 dB according to IRT |
|
| Output |
|
| Type |
balanced, grounded |
| nominal Level |
+ 6 dBu |
| maximum Level1) |
ƒ ³ 40 Hz, kges 1 % ³ + 30 dBu |
| Source Impedance |
ƒ 40 Hz - 15 kHz £ 40 W |
| Load Resistance |
³ 300 W |
| CMRR |
ƒ £ 15 kHz ³ 40 dB according to IEC |
| CMRR |
ƒ £ 15 kHz ³ 60 dB according to IRT |
|
| Gain 2) |
all Mix Controls all to the left 1 kHz 0 dB ± 0.5 dB |
|
| Frequency Response 2) |
ƒ 20 Hz - 20 kHz ± 0.25 dB |
| Phase Response 2) |
- Input/Output ƒ 40 Hz - 15 kHz £ +5/-20°
- with Standard Values for RF & LF Filters
|
|
| THD 3) |
£ +26 dBu, ƒ ³ 40 Hz - 15 kHz, kges £ 0.1 % |
|
| Crosstalk |
, L-R, ƒ 40 Hz - 15 kHz £ 70 dB |
|
| Dynamic Range 2) |
Gain 0 dB / 22Hz-22kHz RMS ³ 120 dB |
| Noise Level 2) |
Gain 0 dB / 22Hz-22kHz RMS £-90 dBu |
|
| Size |
V700-Module - StandardSize |
| Frame |
fits into Standard Frames |
|
| Control Elements |
Stepper Pots - 21 Steps and continuouely variable pots |
| Sections |
|
| Hi |
Low Slew Rate fully parametric EQ band
sweep range from 400 Hz to 20 kHz
q-factor range from 2 octave to 0.5 octave
boost/cut range +/- 6 dB
Mix control from Original only to EQ output only |
| Low |
Very Low Slew Rate fully parametric EQ band
sweep range from 20 Hz to 1 kHz
q-factor range from 2 octave to 0.5 octave
boost/cut range +/- 6 dB
Mix control from Original only to EQ output only |
| FET |
Generation of FET distortion in a level range that is determined by the BIAS control
Mix control from Original only to FET output only |
| DIODE |
Generation of Diode distortion in a level range that is determined by the BIAS control
Mix control from Original only to DIODE output only |
|
- 1)
- Depending on the setting of the control, gain or attenuation is possible. The value is valid for the higher level at the input or output.
|
|
- 2)
- all Distortion Mix Control inactive
|
|
- 3)
- The purpose of this unit is the generation of harmonics distortion. It is self evident that these values are valid for inactive setting of the mix controls.
|
|
| Index |
Home V700 Home |