| Technical Data |
STEREO MONITOR CONTROLLER W760 |
| Version |
V700-Cassette 1N |
|
| Input |
stereo |
| Type |
balanced floating/Transformer |
| nominal Level |
+ 6 dBu |
| maximum Level1) |
ƒ ³ 40 Hz ³ + 30 dBu |
| Input Impedance |
ƒ 40 Hz - 15kHz ³ 25 kW |
| CMRR |
ƒ 40 Hz £ 15 kHz ³ 60 dB according to IRT |
|
| Output |
stereo |
| Type |
balanced floating/Transformer |
| nominal Level |
+ 6 dBu |
| maximum Level1) |
ƒ ³ 40 Hz, kges 1 % ³ + 26 dBu |
| Source Impedance |
ƒ 40 Hz - 15 kHz £ 60 W |
| Load Resistance |
³ 600 W |
| CMRR |
ƒ £ 15 kHz ³ 40 dB according to IEC |
| CMRR |
ƒ £ 15 kHz ³ 60 dB according to IRT |
|
| Gain 2) |
all Controls @ 0 dB - 1 kHz 0 dB ± 0.5 dB |
|
| Frequenzgang |
ƒ 20 Hz - 20 kHz ± 0.5 dB |
| Phase Response |
- Input/Output ƒ 40 Hz - 15 kHz £ +5°/-20°
- with normal LF/RF Filters
|
|
| THD |
£ +26 dBu, ƒ ³ 40 Hz - 15 kHz, kges £ 0.1 % |
|
| Dynamic Range |
22Hz-22kHz RMS ³ 120 dB |
| Noise Level |
22Hz-22kHz RMS £-90 dBu |
|
| Crosstalk |
Links <> Rechts ƒ 40 Hz - 15 kHz £ -70 dB |
|
| Size |
Standard V700-Cassette |
| Frame |
for V700 Standard Frames |
|
| Control Elements |
Stepper Switches/Potentiometers 21 Detents
|
- Volume
|
- 21 Steps from Off to 92 dB-SPL
- Gain at 92 dB-SPL 0 dB ± 0.25 dB
- Matrix Stage and Direction Controls not utilized
|
| Direction |
- 21 Steps from 'Left only' to 'Right only''
- Calibration in % of the half Basewidth
- 0 Stellung ± 0.25 dB
|
|
| Headphones |
- Headphone Output with Level Offset Control for Headphones 4W to 2kW
|
| PFL |
- Activated by Pushbutton or Opto Coupler Input Voltage 9 to 30 V
- separate balanced Input
- Level Control
|
| DIM |
- Control by Pot, Range 10 to 30 dB
- Activated by Switch or Remote Control Opto Coupler Input
|
|
| Mono Matrix |
internal Selection 3 dB or 6 dB Operation |
| L/R Reversal |
by Switch L<>R
|
| Phase Reversal |
right Channel by Switch ØR |
| Muting |
common for all Outputs by Switch CUT |
| 2. Speaker System |
passive, selected by Switch ALT |
|
|
| 1) |
Data refers to the that highest level on input or output |
|
| 2) |
Data refers to linear setting of all parameters. |
|