Technical Specifications
ToolMod TM205
5 Band Stereo Mastering EQ
 OPEN IN NEW WINDOW/TAB | HOME | BACK  | TM205 HOME   |CLOSE| INDEX 
Format ToolMod Module Size 4U
Versions TM205-20h - +/- 20 dB, horizontal Face Plate
TM205-20v - +/- 20 dB, vertical Face Plate
TM205-12h - +/- 12 dB, horizontal Face Plate
TM205-12v - +/- 12 dB, vertical Face Plate
Power Supply Tool-Series Standard
Supply Voltages +/- 25 V and + 48 V Phantom
Supply Current *) +/- 200 mA
Input electronically balanced, Stereo
nominal Level + 6 dBu - Gain
maximum Level > + 30 dBu - Gain
Input Impedance 40 Hz - 15 kHz > 10 kOhms
nominal Source Impedance 50 Ohms
CMRR 15 kHz > 65 dB, typical 75 dB 1 kHz > 80 dB, 40 Hz > 90 dB
Output electronically balanced, Stereo
nominal Level + 6 dBu
maximum Level > + 30 dBu
Source Impedance 50 Ohms, see Diagram
Output Source Resistance vs Frequency
Load Resistor see Diagram
maximum Output Level vs Load Resistor
and
maximum Output Level vs capacitive Load
CMRR according to IEC > 40 dB, siehe Diagram Output CMRR vs Frequency
Gain  0 dB +/- 0.3 dB linear setting
Frequency Response
20 Hz - 30 kHz +/- 0.5 dB linear setting
Bandwidth < 10 Hz to > 150 kHz
Phase Response 20 Hz-20 kHz < +6/-10° linear setting
- see Diagram Phase Response
THD < + 28 dBu, 40 Hz ... 20 kHz, 70 dB Gain < 0.1 %,
maximum THD at + 30 dBu <1 %
Crosstalk > 65 dB, 40 Hz ... 15 kHz
Dynamic Range / Noise
RMS 22Hz-22kHz <= -90 dBu linear setting
total Dynamic Range referring to the RMS Value 22Hz-22kHz
>= 120 dB linear setting
Low EQ active RC-Filter
Soft bell with Center Frequency Selection
40 Hz - 60 Hz - 100 Hz - 160 Hz by 2 Switches
Control Range +/- 20 dB or +/- 12 dB, depending on Version
High EQ aktives RC-Filter
Shelving Filter at Setting 20 kHz,
Soft bell with Setting 12 kHz - 8 kHz and 4 kHz
Frequency Selection by 2 Switches
Control Range +/- 20 dB or +/- 12 dB, depending on Version
Mid 1 EQ fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 20 Hz +/- 10 % to 2 kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 20 dB or +/- 12 dB, depending on Version
Mid 2 EQ fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 20 Hz +/- 10 % to 2 kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 20 dB or +/- 12 dB, depending on Version
Mid 3 EQ fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 60 Hz +/- 10 % to 7 kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 20 dB or +/- 12 dB, depending on Version
Bypass Circuitry Hardbypass by Relay
*) The standard supply current is the supply current under realitic operation conditions. If the outputs are loaded with the minium load resistors and the level is at + 30 dBu, the supply current increases by 30 mA per output. The standard supply current shuold be used to calculate the necessary power supply capacity of a system.