|
 |
|
|
|
|
|
|
Format |
ToolMod Module Size 4U |
|
|
Versions |
TM134 h -
horizontal Face Plate
TM134 v - vertical Face Plate
|
|
|
Power Supply |
Tool-Series Standard |
|
|
Supply Voltages |
+/- 25 V and + 48 V Phantom |
|
|
Supply Current *) |
+/- 200 mA |
|
|
|
|
|
Input |
electronically balanced, Stereo |
|
|
nominal Level |
+ 6 dBu - Gain |
|
|
maximum Level |
> + 30 dBu - Gain |
|
|
Input Impedance |
40 Hz - 15 kHz > 10 kOhms |
|
|
nominal Source Impedance |
50 Ohms |
|
|
CMRR |
15 kHz > 65 dB, typical 75 dB 1 kHz > 80 dB, 40 Hz > 90 dB |
|
|
|
|
|
Output |
electronically balanced, Stereo |
|
|
nominal Level |
+ 6 dBu |
|
|
maximum Level |
> + 30 dBu |
|
|
Source Impedance |
50 Ohms, see Diagram
Output Source Resistance vs Frequency |
|
|
Load Resistor |
see Diagram
maximum Output Level vs Load Resistor
and
maximum Output Level vs capacitive Load |
|
|
CMRR according to IEC |
> 40 dB, siehe Diagram Output CMRR vs Frequency |
|
|
|
|
|
Gain |
0 dB +/- 0.3 dB linear setting |
|
|
|
|
|
Frequency Response
|
20 Hz - 30 kHz +/- 0.5 dB linear setting |
|
|
Bandwidth |
< 10 Hz to > 150 kHz |
|
|
|
|
|
Phase Response |
20 Hz-20 kHz < +6/-10° linear setting
- see Diagram Phase Response
|
|
|
|
|
|
THD |
< + 28 dBu, 40 Hz ... 20 kHz, 70 dB Gain < 0.1 %,
maximum THD at + 30 dBu <1 % |
|
|
Crosstalk |
> 65 dB, 40 Hz ... 15 kHz |
|
|
|
|
|
Dynamic Range / Noise |
|
|
|
RMS 22Hz-22kHz |
<= -90 dBu linear
setting, M/S input & output
<= -88dBu linear setting, L/R input & output |
|
|
total Dynamic Range |
referring to the RMS Value 22Hz-22kHz
>= 120 dB linear setting M/S input & output
118 dB linear setting, L/R input & output |
|
|
|
|
|
operation Mode |
frequency dependent
stereo base width
control |
|
|
Mode Switches |
S: only the S-channel is affected
M: only the M-channel is affected
M/S: boost in S is compensation with cut in M and vice versa |
|
|
Low EQ |
fully parametric Equalizer Band with
active Vienna Bridge Circuitry, with Center Frequency Control
from 20 Hz +/- 10 % to 1kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 8 dB |
|
|
Mid 1 EQ |
fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 50 Hz +/- 10 % to 5 kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 8 dB
|
|
|
Mid 2 EQ |
fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 200 Hz +/- 10 % to 15 kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 8 dB
|
|
|
High EQ |
fully parametric Equalizer Band with active Vienna Bridge Circuitry, with Center Frequency Control
from 400 Hz +/- 10 % to 25 kHz, +/- 10 %
Q-Factor Control from > 3 Octaves to a Third
Control Range +/- 8 dB
|
|
|
|
|
|
INP-MS |
determines the function of the input
matrix
default - L/R to M/S conversion on
pressed - L/R to M/S conversion off |
|
|
OUT-MS |
determines the function of the output
matrix
default - M/S to L/R conversion on
pressed - M/S to L/R conversion off |
|
|
Matrix Options |
default - input and output matrix is
switched with the bypass of the module
alternate setting by jumper - input and output matrix are always on, bypass affects
only the compressor |
|
|
Bypass Circuitry |
Bypass Switches for
each Band
and
Hardbypass by Relay for the entire unit |
|
|
|
|
|
*) The standard supply current is the supply current under realitic operation conditions. If the outputs are loaded with the minium load resistors and the level is at + 30 dBu, the supply current increases by 30 mA per output. The standard supply current shuold be used to calculate the necessary power supply capacity of a system. |
|
|
|
|
|
|
|
|